Miele KM 2257 Instrukcja Użytkownika

Operating and installation instructionsGas hobsKM 2256KM 2257KM 2257-1To avoid the risk of accidents ordamage to the appliance it isessential to read

This gas hob complies with allrelevant local and national safetyrequirements. Inappropriate usecan, however, lead to personal injuryand damage to prop

Safety with children~This gas hob is not a toy! To preventthe risk of injury, do not allow childrento play with the appliance or itscontrols.~Children

Technical safety~Before installation, check the gashob for visible signs of damage. Do notinstall and use a damaged appliance. Adamaged appliance may

~During installation, maintenance andrepair work, the gas hob must bedisconnected from the gas supply andmains electricity supply.~While the gas hob i

Correct use~The gas hob gets hot when in useand remains hot for quite a while afterbeing switched off. Do not touch itwhilst it could still be hot.~If

~Pans must be the correct size for theburner they are used on (see "Suitablepans"). A pan which is too small will beunstable on the pan supp

~Do not use pans that are largeenough to cover more than one burner.The resulting build-up of heat coulddamage the gas hob.~Always ensure that food is

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly fordisposal, and

Please stick the extra data plate for the appliance suppliedwith this documentation in the space provided in the "Aftersales service" sectio

Rapid ignition systemThe appliance is supplied with a rapid ignition system withthe following features:–After the flame is ignited, the hob control ca

G This appliance can be used in countries other than those specified on theappliance. It is, however, set up for connection to the gas and electricity

Switching onWhen using the gas hob an extractor hood or a ventilationdevice must be used.^The control for the burner required must be pressed in andtu

Regulating the flameRegulate the flame so that it does not spread out beyond thesides of the pan. As the outer part of the flame is much hotterthan th

Burner Min. pan base diameter in cmSmallMediumLargeExtra largeWok1010121415Max. diameter at top of pan in cmWithout Withcombi insertSmallMediumLargeEx

Wok ringWoks have a small base diameter and large top diameter,generally between 35 - 40 cm.Use the wok ring supplied to give additional stability,esp

–Use a pan lid whenever possible to minimise heat loss.–Cook with as little water as possible.–Cooking times are greatly reduced when using a pressure

Thermoelectric safety ignitionThis appliance is fitted with a thermoelectric ignition safetydevice. If the flame goes out, for example if food has boi

General notesMiele offer a range of branded cleaning and conditioningproducts. See "Optional accessories".,Do not use a steam cleaning appli

Stainless steel surfacesClean stainless steel surfaces using an E-Cloth (see "Optionalaccessories") or with a solution of warm water and a l

BurnersDo not clean any parts of the burners in a dishwasher.The burners should be dismantled and then cleaned by handusing a solution of warm water a

To assemble the small, medium, large and extra large burners^ Place the burner head r on to the burner base u so thatthe ignition safety device s and

Gas-heated appliancesSafety precautions to take if you smell gasß Turn off the gas emergency control valve immediately.This is usually located near th

To assemble the wok burner^ Place the burner head r on to the burner base u so thatthe the ignition safety device s and the ignitor t extendthrough th

,Repairs to the gas and electrical components of thisappliance must only be carried out by a suitably qualifiedand competent person to ensure safety (

... the gas flame suddenly looks different.Check whether the burner is assembled correctly... the gas flame goes out during operation.–Check whether

Miele offer a comprehensive range of useful accessories aswell as cleaning and conditioning products for your Mieleappliances.These products can be or

This appliance must be installed andconnected to services inaccordance with local and nationalsafety and building regulations.To avoid the risk of dam

Safety distance above the hobA minimum safety distance must bemaintained between the hob and thecooker hood above it. See the cookerhood manufacturer&

Safety distances to the sides of andbehind the applianceIdeally the hob should be installed withplenty of space on either side. Theremay be a wall at

Appliance and building-in dimensionsa Frontb Casing depthc Gas connection R 1/2 - ISO 7-1 (DIN EN 10226)d Electrical connectione Electronics housing 1

Installation^Make the worktop cut-out accordingto the dimensions given in thebuilding-in dimension diagram.Remember to maintain the minimumsafety dist

SealantThe sealing strip under the edge of thetop part of the hob provides a sufficientseal for the worktop.The appliance must not be sealedwith seala

Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6GasHob...

Appliance and building-indimensionsa Frontb Casing depthc Gas connection R 1/2 - ISO 7-1(DIN EN 10226)d Electrical connectione Electronics housing 100

Flush fit gas hobs are only suitablefor installation in granite, marble,tiled or solid wood worktops. Whenusing a worktop made from anyother material,

InstallationGranite and marble worktopsa Worktopb Fixing bracket (the fixing bracketshold the lower section when theupper section of the hob isremoved

Solid wood and tiled worktopsa Worktopb Fixing bracket (the fixing bracketshold the lower section when theupper section of the hob isremoved).c Hobd G

Appliance and building-indimensionsa Frontb Casing depthc Gas connection R 1/2 - ISO 7-1(DIN EN 10226)d Electrical connectione Electronics housing 100

Flush fit hobs are only suitable forinstallation in granite, marble, tiled orsolid wood worktops. When using aworktop made from any othermaterial, ple

InstallationGranite and marble worktopsa Worktopb Hobc GapAs the hob and worktop cut-out maydiffer, the size of the gap c can vary.^Make the worktop c

Solid wood and tiled worktopsa Worktopb Hobc Gapd Wooden frame 7 mm (to be providedon site)As the hob and worktop cut-out maydiffer, the size of the g

Building into a stainless steel worktopThis appliance can be welded into a stainless steel worktop. It is essential thatafter being welded, it is stil

Secure the appliance as shown, usingthe fixings supplied.20 mm worktop30 mm worktop40 mm worktopAfter installationCheck that all the burners are opera

Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Safety instructions for installation

All electrical work should be carriedout by a suitably qualified andcompetent person in strictaccordance with current local andnational safety regulat

ImportantThe electrical safety of this appliancecan only be guaranteed whencontinuity is complete between theappliance and an effective earthingsystem

,Connection to the gas supply, orconversion from one type of gas toanother, should only be undertakenby an approved and registered gasinstaller in str

ConnectionThe gas connection must be installedso that connection can be made eitherfrom inside or outside the kitchen unit,and the isolating valve mus

Nominal ratingBurner Gas type High setting Low settingkW g/h kWSmall burner Natural gas HLiquid gas1.000.95-690.2500.300Medium burner Natural gas HLiq

When converting to another type ofgas, the main jets and the small jetson all burners have to be changed.Screw in new jets appropriate to thetype of g

Changing the jetsDisconnect the gas hob from theelectricity supply by switching off atthe socket and withdrawing theplug, by disconnecting the mainsfu

Wok burner^ Remove burner caps op, burnerring q and burner head r.^ Remove the controls.^ Loosen screws w, and remove theburner base.^ Whilst counterh

To change the jet for the inner burnerd Jet disc (main jet for the innerburner)e Air intakef Vent^Whilst counterholding it in place withan SW 12 spann

To check the first intake of aira Retaining screwb Air intakeGap X must measure:For natural gas: 6 mmFor liquid gas: 13 mmTo adjust gap X:^Loosen the

Gas HobKM 2256 / KM 2257 / KM 2257-1a Small burnerb Extra large burnerc Wok burnerd Large burnere Medium burnerf Pan support (in three sections)g Comb

To change the small jetsTo change the small jets, the burnersecuring screws must first be loosenedand the upper section of the applianceremoved.^Pull

Function testCarry out a gas leakage test.Reassemble the hob in the reverseorder. Ignite all the burners to checkthat they are operating correctly.The

In the event of any faults which you cannot remedy yourself, or if the appliance isunder guarantee, please contact:–Your Miele dealer, or–the Miele Se

63

Alteration rights reserved / 4311M.-Nr. 07 072 451 / 05

BurnerWok burnero Inner burner capp Outer burner capq Burner ringr Burner heads Ignition safety devicet Ignitoru Burner basePosition of burner compone

Small, medium, large and extra largeburnersn Burner capr Burner heads Ignition safety devicet Ignitoru Burner baseGuide to the appliance8

AccessoriesWok ringThe wok ring supplied gives additional stability to the wok,especially to those with a rounded base.Combi insert for small and larg